[수입판매] Pepperl + Fuchs Thru-beam sensor OBE40M-R200-S2EP-IO-V1-L 포토센서
- 다양한 장착 옵션이 있는 중간 디자인
- DuraBeam 레이저 센서 - 내구성이 뛰어나고 LED처럼 사용 가능
- 서비스 및 프로세스 데이터용 IO-Link 인터페이스
- 상호 간섭 방지를 위한 다양한 주파수(누화 내성)
- 확장된 온도 범위 -40°C ... 60°C
- 높은 보호 등급 IP69K
| System components | ||
| Emitter | OBE40M-R200-S-IO-V1-L | |
| Receiver | OBE40M-R200-2EP-IO-V1-L | |
| General specifications | ||
| Effective detection range | 0 ... 40 m | |
| Threshold detection range | 50 m | |
| Light source | laser diode | |
| Light type | modulated visible red light | |
| Laser nominal ratings | ||
| Note | LASER LIGHT , DO NOT STARE INTO BEAM | |
| Laser class | 1 | |
| Wave length | 680 nm | |
| Beam divergence | > 5 mrad ; d63 < 2 mm in the range of 250 mm ... 750 mm | |
| Pulse length | 1.6 µs | |
| Repetition rate | max. 17.6 kHz | |
| max. pulse energy | 9.6 nJ | |
| Alignment aid | LED red (in receiver lens) illuminated constantly: beam is interrupted, flashes: reaching switching point, off: sufficient stability control | |
| Diameter of the light spot | approx. 80 mm at a distance of 40 m | |
| Opening angle | approx. 0.12 ° | |
| Ambient light limit | EN 60947-5-2 : 40000 Lux | |
| Functional safety related parameters | ||
| MTTFd | 440 a | |
| Mission Time (TM) | 20 a | |
| Diagnostic Coverage (DC) | 60 % | |
| Indicators/operating means | ||
| Operation indicator | LED green: constantly on - power on flashing (4Hz) - short circuit flashing with short break (1 Hz) - IO-Link mode | |
| Function indicator | Yellow LED: Permanently lit - light path clear Permanently off - object detected Flashing (4 Hz) - insufficient operating reserve | |
| Control elements | Receiver: light/dark switch | |
| Control elements | Receiver: sensitivity adjustment | |
| Electrical specifications | ||
| Operating voltage | 10 ... 30 V DC | |
| Ripple | max. 10 % | |
| No-load supply current | Emitter: ≤ 13 mA Receiver: ≤ 15 mA at 24 V Operating voltage | |
| Protection class | III | |
| Interface | ||
| Interface type | IO-Link ( via C/Q = pin 4 ) | |
| IO-Link revision | 1.1 | |
| Device profile | Identification and diagnosis Smart Sensor: Receiver: type 2.4 Emitter: - | |
| Device ID | Emitter: 0x111402 (1119234) Receiver: 0x111302 (1118978) | |
| Transfer rate | COM2 (38.4 kBit/s) | |
| Min. cycle time | 2.3 ms | |
| Process data width | Emitter: Process data input: 0 bit Process data output: 1 bit Receiver: Process data input: 2 bit Process data output: 2 bit | |
| SIO mode support | yes | |
| Compatible master port type | A | |
| Input | ||
| Test input | emitter deactivation at +UB | |
| Output | ||
| Switching type | The switching type of the sensor is adjustable. The default setting is: C/Q - Pin4: NPN normally open / dark-on, PNP normally closed / light-on, IO-Link /Q - Pin2: NPN normally closed / light-on, PNP normally open / dark-on | |
| Signal output | 2 push-pull (4 in 1) outputs, short-circuit protected, reverse polarity protected, overvoltage protected | |
| Switching voltage | max. 30 V DC | |
| Switching current | max. 100 mA , resistive load | |
| Usage category | DC-12 and DC-13 | |
| Voltage drop | ≤ 1.5 V DC | |
| Switching frequency | 1250 Hz | |
| Response time | 0.4 ms | |
댓글 없음:
댓글 쓰기